GM International D6072D-099 SIL2 Sink-Out Temperature Converter

GM International D6072D-099 SIL2 Sink-Out Temperature Converter

Artikelnummer: GMI20250286
Hersteller: GM International

458,00 €

exkl. 19% USt. , zzgl. (National)

Sofort verfügbar
Lieferzeit: 24 - 26 Werktage (Ausland)

Beschreibung

FEATURES

SIL 2 / SC 3
Installation in Zone 2
Installation in Div. 2
mV, TC, 2/3/4wire res./RTD or potentiometer input
Duplication/inversion/scaling/custom output
Selectable CJC: internal PT1000, external RTD or fixed
Burnout/internal/cjc/in sensor fault monitor
Alarm output with user-settable trip points
Modbus RTU RS-485 for monitor & configuration
Fully programmable operating parameters
High Accuracy, µP controlled A/D converter
Three port isolation, Input/Output/Supply
High Density, two channels per unit

STATUS

ACTIVE

CHANNELS

Technical Data

Supply
Voltage	24 Vdc nom (18 to 30 Vdc), reverse polarity protected
Current Consumption	50 mA @ 24 Vdc with 20 mA out, typical.
Power Dissipation	1.0 W @ 24 Vdc with 20 mA out, typical.
Input
Type	Millivolt, thermocouple, 2-3-4 wire RTD or 3 wire transmitting potentiometer. Refer to Instruction Manual for more details.
Integration time	from 50 ms to 500 ms.
Input range	±500 mV (TC/mV), 0-4 kΩ (RTD/res), up to 10 kΩ (pot).
Thermocouple reference junction compensation	programmable: internal Pt1000, fixed, external, or remote.
Output
Type	Fully customizable 0/4 to 20 mA (sink mode), current limited @ 24 mA. External voltage generator range is V min. 3.5V @ 0Ω load and V max. 30V.
Transfer characteristic	linear, direct or reverse on all input sensors.
Modbus interface
Type	Modbus RTU RS-485 up to 115.2 kbps for monitor/configuration/control.
Input performance
Ref. Conditions	24 V supply, 250 Ω load, 23 ± 1 °C ambient temperature, slow integration mode, 3/4 wires configuration for RTD.
Calibration and linearity accuracy	refer to Instruction Manual.
Temp. influence	refer to Instruction Manual.
Ref. junction compensation accuracy	≤ ±3 °C (internal CJC), ≤ ±1.5 °C (external local CJC), according to RTD (external remote CJC). Refer to Instruction Manual.
Output performance
Ref. Conditions	24 V supply, 250 Ω load, 23 ± 1 °C ambient temperature, slow integration mode, 3/4 wires configuration for RTD.
Calibration accuracy	≤ ± 10 µA.
Linearity accuracy	≤ ± 10 µA.
Temp. influence	≤ ±1 μA for a 1 °C change.
Isolation
Test Voltage	In/Out 2.5 kV; In/Supply 2.5 kV; In/In 500 V; Out/Supply 500 V; Out/Out 500 V.
Environmental conditions
Operating temperature	temperature limits –40 to +70 °C.
Storage temperature	temperature limits –45 to +80 °C.
Mounting
Type	DIN-Rail 35 mm, with or without Power Bus or on custom Term. Board.
Weight	about 135 g
Connection	by polarized plug-in disconnect screw terminal blocks to accommodate terminations up to 2.5 mm² (13 AWG).
Dimensions	Width 12.5 mm, Depth 123 mm, Height 120 mm.