GM International D2010M Intrinsically Safe Analog-Temperature Multiplexer DIN-Rail Model D2010M

GM International D2010M Intrinsically Safe Analog-Temperature Multiplexer DIN-Rail Model D2010M

SKU: GMI20250122
Manufacturers: GM International

$ 4253,47

excl. 19% VAT , plus (National)

Available immediately
Delivery time: 3 - 5 Workdays (Other countries)

Description

FEATURES

Intrinsically Safe for installation in Zone 1, 2 Gas Group IIC, IIB, IIA T4 or Class I, Division 1, 2 Groups A, B, C, D, Temperature Code T4 and Class I, Zone 1, 2 Groups IIC, IIB, IIA, Temperature Code T4 Hazardous Area/Hazardous Location.
Universal inputs (mV, TC, RTD) from Zone 0, 1, 2 or Class I, II, III, Division 1, 2, Groups A, B, C, D, E, F, G, and Class I, Zone 0, 1, 2 Groups IIC, IIB, IIA Hazardous Location.
Isolation of 200 V input to input (mV or TC), 60 V input to input (RTD) and 500 V input to ground, allows grounded sensors.
Expandability up to 256 analog channels per system and 31 systems on a single Modbus serial link for up to 7936 channels.
Redundant field lines for communication/supply.
High accuracy A/D converter, 18 bits.
EMC Compatibility to EN61000-6-2, EN61000-6-4.
High density, 16 channels per unit, 256 channels per system.
Configurable via D2050M Gateway using PC SWC2090 software (free of charge) or user software.
Modbus output allows savings on PLC/DCS I/O cards cost.
Lower cables, installation and maintenance costs.
1 terminal block per input, no external terminal block required.

Technical Data

Supply
Voltage	via D2050M gateway unit.
Max. power consumption	200 mW.
Input
Type	millivolt or thermocouple type A1, A2, A3, B, E, J, K, L DIN, L GOST, N, R, S, S GOST, T, U or 3-4 wires RTD Pt100, Pt200, Pt300 to DIN43760, Pt100 (0.3916), Ni 100 or Pt100, Pt50, Cu100, Cu53, Cu50, Cu 46 (GOST) or mA signals with external shunt (D1090Q) or V signals with external divider (D1094Q).
Input channels	16 for mV, RTD or TC without automatic reference junction compensator or 15 using automatic reference junction compensator for thermocouples inputs (channel 16 is used for compensator connection).
Resolution	2 μV on mV or thermocouple, 10 mΩ on RTD.
Input range	within sensor’s rated limits; mV range from - 21 to + 80 mV or - 21 to + 21 mV, resistance range from 0.0 to 400.0 Ω.
Measuring RTD current	≤ 200 μA.
RTD line resistance compensation	≤ 10 Ω.
Thermocouple reference junction compensation	automatic with external sensor on channel nr. 16 (OPT2091 separately ordered or user selectable RTD) or fixed programmable from - 60 to + 100 °C.
Burnout	up, down or disabled.
Scan cycle time	1700 ms for a system with 4 D2010M and 12 D2011M (256 ch.).
Performance
Type	field units powered by D2050M gateway at 23 ± 1 °C ambient temperature.
Calibration and linearity accuracy	≤ ± 20 μV on mV or thermocouple, 200 mΩ on RTD or ± 0.05 % of input value, whichever is greater.
Temperature influence	≤ ± 2 μV, 10 mΩ or ± 0.01 % of input value for a 1 °C change.
Ref. Junction Compensation influence	≤ ± 1 °C (thermocouple sensors only).
Isolation
Test Voltage	I.S. In/Supply-Communication line 500 V; I.S. In/I.S. In 200 V for mV/TC, 60 V for RTD; I.S. In/Ground 500 V; I.S. In/I.S. In between units 500 V. Communication line/Ground 500 V;
Storage	temperature limits – 40 to + 60 °C, relative humidity max 90 % non condensing, up to 35 °C.
Environmental conditions
Operating	temperature limits – 40 to + 60 °C, relative humidity max 90 % non condensing, up to 35 °C.
Storage	temperature limits – 45 to + 80 °C.
Safety description
Safety parameters	Uo/Voc = 10.7 V, Io/Isc = 7 mA, Po/Po = 19 mW at terminals 1-2-3-4 of channel 1 to 16. -40 °C ≤ Ta ≤ 60 °C.
Weight	T35 DIN Rail according to EN50022.
Connection	about 750 g.
Location	by polarized plug-in disconnect screw terminal blocks to accomodate terminations up to 2.5 mm².
Protection class	Safe Area/Non Hazardous Locations or Zone 1, 2, Group IIC, IIB, IIA T4, Class I, Division 1, Groups A, B, C, D Temperature Code T4 and Class I, Zone 1, 2, Group IIC, IIB, IIA T4 installation.
Dimensions	IP 20.
Mounting
Type	T35 DIN Rail according to EN50022.
Weight	about 750 g.
Connection	by polarized plug-in disconnect screw terminal blocks to accomodate terminations up to 2.5 mm².
Location	Safe Area/Non Hazardous Locations or Zone 1, 2, Group IIC, IIB, IIA T4, Class I, Division 1, Groups A, B, C, D Temperature Code T4 and Class I, Zone 1, 2, Group IIC, IIB, IIA T4 installation.
Protection class	IP 20.
Dimensions	Width 127 mm, Length 220 mm, Depth 78 mm.

Shipping weight:	1,00 kg
Item weight:	0,75 kg
Dimensions ( Length × Width × Height ):	25,00 × 19,00 × 18,00 cm
Zustand / Condition:	Neu / New

Product safety information

Manufacturer information:

G.M. International srl
Via G. Mameli 53-55
Monza e Brianza
Villasanta, Italien, 20852
info@gminternational.com
https://gminternational.com/

GM International D2010M Intrinsically Safe Analog-Temperature Multiplexer DIN-Rail Model D2010M

Supply

Input

Performance

Isolation

Environmental conditions

Safety description

Mounting